If you have a router at home and want to extend the range of your Wi-Fi signal, you don’t necessarily need a Wi-Fi repeater with WPS. Often, you can connect a Wi-Fi extender without WPS simply by using your router’s Wi-Fi settings and choosing the correct password.
WiFi extender setup is known as the ultimate method to increase the range and speed of the current wireless network. A router is enough to reach the Internet signals to cover a small house with a WiFi connection, but it cannot cover a large apartment or office. Therefore, you cannot transmit the Internet to the dead zones of your home. In this case, setting up a WiFi extender helps solve the problem. After completing the WiFi extender setup, the existing WiFi signals from the router will be re-broadcast to provide you with WiFi in every corner of your home.
Connect the Ethernet cable from your router to your PC by unplugging the end. You can then connect it to the range extender. A range extender will be able to communicate with the PC via Ethernet.
You need to know all of this to log in. If you can’t remember or have no idea about the details above, there is a solution.
Your IP address: This is a numerical label assigned to your device.
SSID: This is the name of your network.
Your password.
- Open the command prompt.
- Write this in ‘ipconfig/all’
- All letters must be lowercase.
- You will see all the information needed to log in.
- Enter all the necessary information to log in.
- Sign in now.
How to connect a Wifi extender to the router without WPS?
If you don’t have a WPS button on your router, you can use the extender’s web-based setup method to connect the WiFi extender to the router without WPS. Please see the steps below to configure the repeater on the router without WPS. You must carefully follow these steps:
Step 1:
First, take an Ethernet cable. Connect one end of the Ethernet cable to the Internet port of the extender and the other end to the Internet port of the wireless router.
Step 2:
If you’ve had the same site system for a while and haven’t set it up yourself, set up your WiFi extender.
Step 3:
After that, connect one end of the Ethernet cable to the LAN port of the extender and the other end of the Ethernet cable to the Ethernet connector of each of the devices that have a network connection.
Step 4:
Open a default web browser on your computer. Enter the IP address of your Wi-Fi extender in the address bar of the web browser.
Step 5:
Once you have entered the extender’s IP address, the router’s configuration web page will appear on the screen. Click on the wireless option and enter the name of the wireless network in the SSID or network field. Press the Save button.
Step 6:
In the next step select wireless protection and then choose the security type as WEP. Enter your network password.
Step 7:
Your options may be different depending on the operating system you are using.
Step 8:
Next, unplug the Ethernet cables from the router and WiFi extender.
Step 9:
Finally, place your range extender within range of the router.
How to configure Linksys Extender without WPS configuration?
However, if you don’t want to go through this method, here are some of the steps you can follow to set up the Linksys Extender.
Step 1 :
You have an Ethernet cable and use it to connect your computer system to the range extender.
Step 2:
After that, connect your range extender to the power source. Also, you need to make sure that the LED light is on.
Step 3:
Launch your internet browser and enter the IP address in the address bar of the router.
Step 4:
A window will open in front of you asking you to enter your password and username. There you need to leave the username section blank and enter admin in the password section. After that choose the login option.
Step 5:
Click on Wireless and then select the basic wireless settings option.
Step 6:
Change the radio button to the manual, then enter the network name of the router.
Step 7:
In the next step, you have to select the security settings and then enter the network name of your router.
Step 8 :
Enter the WEP key or passphrase in the search bar, and then save the settings.
Step 9:
Unplug the power cord of the range extender and router and leave it unplugged for the next 30 seconds.
Step 10:
Do not proceed until you find the lights are stable, then reconnect the range extender.